| HINGES |
 |
SF5
PRISON HINGES
· Full surface hinge for hollow metal or steel plate doors.
· Heavy weight for the detention environment.
· Constructed for high abuse areas.
· Can be used on cell or corridor doors, security vestibules, doors,
and primary entrances.
· Also suitable for armories or drug storage areas, or access panels
in high abuse areas.
· ½" thick drop-forged steel leaves.
· Two thrust bearings, with ¼" hardened steel ball
bearings and races.
· Knurled, hardened hinge pin of ¾" diameter steel,
pressed into a blind hole.
· Tamper resistant.
· Non-handed (reversible)
· Oil hole in barrel of male leaf.
· Mounting screws provided with six ½" - 13 x 7/8"
flat head security screws.
· USP primed finish.
· Optional features include welded application (without holes),
specified screw locations, welded pin construction. |
 |
MORTISE
HINGES
· Designed for swinging hollow metal doors.
· Each hinge features cast stainless steel leaves with integral
security stud and non-removable steel pin.
· Security fasteners are provided with each unit.
· Standard stainless steel finish.
· Hinge leaves made of cast stainless steel.
· Stainless steel hinge pin.
· Size: 4½" x 4½" x 3/16".
· Weight - 1.5 lbs. |
| SWITCHES |
 |
CONCEALED
POSITION SWITCH
· Used where a built-in door indicator switch is desired.
· Tamper proof unit that is mortised into the door and frame.
· Indicator switch is mechanically activated when the door is moved
from the closed position.
· Switch adjustment is provided to allow for varying field conditions.
· Provided with security fasteners.
· Handed design, specify LH or RH, but can be reversed in the field.
· 180 degree maximum swing.
· 12" long, 16 AWG UL wire leads with plug connector.
· An eccentric stud on the control arm provides a fine adjustment
for varying conditions.
· Optional features include a double circuit (specify 240CPS-2),
which allows for an additional circuit to be triggered by the 240CPS.
· Concealed in frame.
· Control arm of 5/16" thick steel and zinc plated.
· Stainless steel face plate.
· Switch is SP.D.T. type with a rating of 5 amps at 30 VDC to 250
VAC.
· Weighs 2 lbs. |
 |
MAGNETIC
REED SWITCH
· Used where a built-in door indicator switch is desired.
· Tamper-proof.
· Mortised into doorframe.
· Actuating magnet is recessed into the door edge.
· Provided with security fasteners.
· Weighs 1 lb.
· Size: 4-7/8" L x 1¼" W
· 24 volts (AC or DC)
· Optional Triple Bias Switch available - specify TB. |
 |
MECHANICAL
220A DOOR POSITION SWITCH
· Actuates a remote lamp indicator or an audible signaling device
the moment a swinging door is moved from the fully-closed position.
· Enclosed in a 10-gauge galvanized steel housing.
· Designed for installation on the doorframe above the top hinge.
· A pivoting operator that actuates the switch is attached to the
doorframe with special security screws.
· Designed for use on doors with 4½" or 5" hinges.
· Provided with security fasteners.
· Size: 6¼" x 2½" x 1-7/8".
· Weighs 3 lbs.
· Switch rating. SPDT 15 amps at 125 VAC or 0.5 amps at 125 VDC. |
| DOOR
PULLS |
 |
RAISED
DOOR PULLS
· Economical.
· Attractive.
· General all purpose door pull.
· Designed for ease of operation on heavy doors and/or heavy traffic
areas.
· Provided with security fasteners.
· Cast brass construction. |
 |
RECESSED
DOOR PULLS
· Adequate size for easily manipulating large, heavy doors.
· Often used on the inmate side of doors.
· Provided with security fasteners.
· Cast brass construction. |
